Fascia wrapping
Coil stock wrap is bent to fit over solid boards to cut down on painting.
Exterior Services
Fascia Repair North Arlington, NJ
A roofing contractor in North Arlington can fix soft, split or loose fascia along the roof edge, whether it is painted wood, PVC or wrapped in aluminum, and check the rafter tails behind the board while it is off. Dial (551) 348-7205 to talk with a local roofer about the fascia.
Fascia rot nearly always comes from water getting behind the gutter. Clogged or poorly pitched gutters spill over the back, and a roof edge with no drip edge sends water straight down the fascia. The wood slowly loses strength until the gutter spikes or hanger screws no longer hold.
Fascia damage does not stay in the fascia for long. Behind the board are the rafter tails, the roof decking at the edge and the soffit, and water that gets past the fascia soaks into all of them. Metal-wrapped fascia is especially tricky because water can get trapped behind the wrap and rot the wood out of sight.
It helps to know what you are seeing before you call. Write down which sides of the house show peeling paint, gaps or a sagging gutter. Mention whether the fascia is painted wood, PVC or covered in aluminum, and how old the gutters are.
Many fascia repair calls in North Arlington also turn up a need for soffit repair or gutter installation.
Dealing with this in North Arlington, NJ right now? Call (551) 348-7205 and describe the problem to a roofer who works in North Arlington.
Call nowThe process
The fascia repair process
A fascia repair only lasts if the water that rotted it is redirected.
Find the water path
Before the board comes off, the roofer looks at what has been soaking it, from the shingle edge to the downspout. Probing along the board shows where the rot starts and stops.
Remove the gutter
To reach the fascia, the gutter over it is removed and the hangers pulled. Old spikes and loose hangers are not reused.
Repair the framing
Soft rafter tails are cut back and sistered with new lumber, and rotted decking at the edge is replaced. Skipping it is the most common reason fascia fails twice.
Replace the boards
The new board is fastened to the rafter tails with corrosion-resistant nails or screws, with tight joints at the corners. End grain is sealed so it does not soak up water.
Reset the drip edge
Drip edge flashing is slid under the shingles and over the gutter back, so water cannot reach the wood. It is a small part that does most of the work.
Reattach gutters
The gutter is reattached with hangers spaced closely enough to carry water and debris. Wood fascia gets a finish coat of paint.
What is included
What fascia repair covers
Edge flashing
Missing or bent drip edge is replaced at the roof edge so water drops into the gutter.
Rotted board repair
Damaged fascia is replaced with primed wood or PVC so gutters have solid backing.
Rafter tail repair
Rotted rafter ends behind the fascia are sistered or rebuilt to keep the roof edge straight.
Gutter rehanging
Loose gutters are refastened and pitched toward downspouts so they drain instead of overflowing.
Related service
Fascia Board Replacement North Arlington, NJ
Fascia board replacement means taking off whole lengths of board rather than patching short sections. The gutters come down, the old boards come off and the rafter tails behind them are checked before new boards go up. The choice of material affects upkeep, since wood needs paint while PVC and wrapped boards do not.
Timing fascia replacement with a reroof in North Arlington lets the new drip edge and the new boards go on together. Be wary of any plan that covers rotted boards with metal instead of replacing them. Matching the board width keeps the soffit and gutter lined up.
Related service
Fascia Board Repair North Arlington, NJ
Fascia board repair handles damage that is limited to a few spots, such as a rotted corner, the area under a leaky gutter seam or a section by a downspout. Angled joints hold paint and shed water better than straight cuts, so they are the standard for patch repairs. Very small areas of surface rot can sometimes be treated with a wood consolidant and exterior filler, then primed and painted.
The repair is only worth doing if the water source is fixed at the same time. Common fixes include a resealed gutter joint, a cleared outlet or a new length of drip edge. Done right, the repair is hard to spot once painted.
Local help
Fascia Repair Near Me
Fascia repair calls in North Arlington come from older homes with painted wood trim and newer homes with aluminum-wrapped edges alike. Homes in North Arlington and nearby towns like Kearny, Rutherford, East Rutherford and Secaucus range from older houses with wood fascia that needs regular paint to newer builds where metal wrap can hide rot underneath, and replacing a short section early is far easier than rebuilding the roof edge later.
Searching for fascia repair near me from North Arlington or Kearny, Rutherford, East Rutherford and Secaucus? Call (551) 348-7205 to talk to a roofer who works in your part of town.
How the weather here affects roofs around North Arlington
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in North Arlington, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why not wait
Drier ceilings
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Familiar with local homes
Roofers in North Arlington know the roof types and weather wear common in local homes.
Clear next steps
Ask your questions before you agree to anything.
Common questions about fascia repair
Which fascia material lasts longest?
Rot-proof materials such as PVC and composite last longest. Primed wood is easy to match on older homes but needs regular paint. The drip edge and gutters decide how long any fascia lasts.
Do I need new fascia boards or just a repair?
Repair is fine when damage is limited to a few spots and the rafter tails are sound. When rot runs along most of a wall or the boards are split throughout, full replacement makes more sense. The roofer will probe the wood to see which option fits.
Why is my fascia rotting?
Fascia rots when water runs down the board instead of into the gutter. A missing drip edge, clogged gutters and leaking gutter seams all keep the wood wet after every rain. Bare end grain and failed paint let water soak in faster.
Should I cover rotted fascia with metal?
Wrapping over soft fascia traps moisture and lets the rot continue unseen. The gutter hangers still screw into the wood behind the wrap, so they loosen as the board softens. Fix the wood, then add wrap over it.
Do fascia boards affect my gutters?
Gutters hang from the fascia, so their strength depends on it. Soft fascia lets the fasteners work loose, which is often the first sign of rot. The fix is solid wood plus new hangers, pitched toward the downspout.
More questions? Call (551) 348-7205
Related services
Soffit Repair
Fixing damaged soffits, blocked soffit vents and gaps where animals get in, before rot spreads into the fascia and rafter tails.
Learn moreGutter Installation
Seamless gutter installation sized to the roof, pitched to the downspouts and hung on hidden hangers, from K-style aluminum to half-round and copper.
Learn moreGutter Repair
Gutter repair for leaking seams, sagging runs, loose hangers and broken downspouts, before the leaks rot the fascia behind them.
Learn moreRoof Repair
Targeted roof repairs for wind, age and water damage, without replacing a roof that still has life left.
Learn more
Looking for something else?
See all roofing servicesTalk to a North Arlington roofer about fascia repair
Call (551) 348-7205 for a local roofer in North Arlington and nearby towns.