Drip edge
Drip edge is added where it was left off with the underlayment lapped correctly.
A North Arlington roofer can stop leaks where the roof meets a wall, dormer, skylight or edge by renewing the flashing at that joint, woven correctly with the shingles and tucked behind the siding. Dial (551) 348-7205 to talk with a local roofer about the flashing.
Shingles handle the open field of a roof; flashing handles the joints. The main types are step flashing at sidewalls, apron flashing at headwalls, counter flashing over the top, kickouts at the bottom of walls, valley metal and drip edge at the edges. When any piece is missing, loose or rusted through, water gets behind the roof covering.
A failed kickout or step flashing tends to rot wall sheathing long before it stains a ceiling. Without a kickout, roof runoff dumps against the siding where the wall meets the eave, soaking the sheathing and framing below it. By the time it is visible, the repair may include some siding and wall sheathing too.
A bead of sealant along a joint is a warning sign, not a repair. Sealant smeared where flashing should be dries and cracks in a few seasons, and it can trap water instead of shedding it. A real repair replaces the metal, often by removing a few courses of siding and shingles so the new flashing can be lapped correctly.
Many flashing repair calls in North Arlington also turn up a need for chimney flashing repair or roof leak repair.
Need flashing repair in North Arlington? Call (551) 348-7205 to talk to a local roofer.
Call nowHere is how a roofer typically approaches a flashing repair.
The flashing is checked along its full length, from the eave up, along with the wall sheathing where it can be seen. Soft siding or stained trim below the joint suggests the wall needs a look too.
Siding is lifted or removed along the joint so the old flashing and housewrap can be reached. That is the only way to lap new metal behind the wall weather barrier.
Each new step piece overlaps the one beneath it, and the kickout at the base sends water into the gutter. Each piece is nailed through the roof side only, so the wall and roof can move independently.
The weather barrier laps over the step flashing, and siding is reinstalled with clearance above the roof surface. That clearance keeps the siding from soaking up water at the roof line.
At the roof edges, drip edge is reset or replaced to protect the fascia and deck edge. The lap order differs at eaves and rakes, and getting it right matters.
Drip edge is added where it was left off with the underlayment lapped correctly.
Headwall metal at the top of a slope is replaced and covered by the siding or counter flashing.
Sidewall flashing is rebuilt one course at a time so water stays on the roof.
Missing kickout diverters are installed at the base of sidewalls which protects the wall below.
Loose counter flashing is secured so the top edge of the step flashing stays covered.
The scope of a flashing repair depends on the joint and on how much damage the water has done. Minor work includes refastening loose metal or adding a missing kickout; bigger jobs mean pulling siding and replacing every step piece along a wall. The roofer should explain which applies before work begins.
Material matters too. Copper outlasts most roofs, galvanized steel is durable and aluminum is light and easy to bend, though it corrodes in contact with wet masonry. Mixing copper with aluminum or galvanized metal in contact can cause corrosion, so the roofer matches the metal to what is already there.
A valley is where two roof slopes meet, and it channels a large share of the roof water toward the eave. Valleys are either open, with exposed metal, or closed, with shingles running through them. Either way, a self-adhered membrane should line the valley under everything else.
Valley leaks often come from debris, worn shingles or nails driven too close to the center. Small installation details, like clipping the upper corners of the cut shingles, keep water flowing down the valley instead of across it. A valley that leaks is generally rebuilt rather than patched.
In North Arlington, many flashing problems date back to an old reroof where the original flashing was reused or caulked instead of replaced. From North Arlington out to neighboring towns such as Kearny, Rutherford, East Rutherford and Secaucus, older homes often have rusted or face-nailed flashing, while newer ones sometimes lack kickouts entirely, so a close look at every joint is worth asking for.
Searching for flashing repair near me from North Arlington or Kearny, Rutherford, East Rutherford and Secaucus? Call (551) 348-7205 to talk to a roofer who works in your part of town.
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in North Arlington is busiest after a hard winter and before the next one.
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Roofers in North Arlington know the roof types and weather wear common in local homes.
Ask the roofer about the cause, the options and the estimate before work starts.
More questions? Call (551) 348-7205
Fixing leaks around the chimney with new flashing set into the mortar joints, with a cricket added where the chimney is wide.
Learn moreFinding where water gets through the roof and sealing it at the source, so the stain on the ceiling stops growing.
Learn moreSkylight repair from the flashing on the roof to the glass and the frame, so the opening stays dry through every storm.
Learn moreVent and pipe boot repairs for leaks, hail damage and worn-out parts, so every opening in the roof stays sealed.
Learn moreLooking for something else?
See all roofing servicesCall (551) 348-7205 for a local roofer in North Arlington and nearby towns.